Product details
Specifications:-
Product Name
SpeedyBee F405 V5 30.5×30.5mm Model Aircraft Flight Controller
MCU
STM32F405
IMU (Gyro)
ICM42688P
USB Port Type
New Type-C interface
Barometer
SPA06-003
OSD Chip
AT7456E
Full-featured Bluetooth Tuning
Supported. Connect via SpeedyBee App for FC firmware flashing and parameter tuning.
Wireless FC Firmware Upgrade
Supported
DJI Air Unit Connection
Supports 6-pin direct plug-in or solder connection
Blackbox
Supported, built-in 16MB storage chip
Input Voltage
3-6S LiPo battery
Independent 5V BEC Output
9 groups (4× +5V pads on front, 1× BZ+ buzzer pad, and 4× +5V pads at the corners for external LEDs). Total output current: 1.5A.
Independent 9V BEC Output
2 groups (1x 9V pad on front, 1x 9V output in a connector on the back). Total output current: 3A. Supports PINIO remote on/off control.
MCU & Gyro Power
Independent LDO
3.3V Output
1 group (1× 3.3V pad on front)
4.5V Output
3 groups (3× 4.5V pads on front). Can power receiver and GPS when FC is powered via USB. Max output current: 1A.
ESC Signal
M1-M4 pads and 10-pin connector on the back
Servo Signal
S5-S6 pads on the front
ESC Telemetry Input
Supported (UART5)
Betaflight Camera Tuning Pad
Supported (CC pad on front)
I2C
Supported (GPS connector + pads)
UART
UART1 (Bluetooth); UART2 (front pads for receiver); UART3 (DJI VTX pads + rear SH1.0-6-pin); UART4 (GPS pads + front SH1.0-6-pin); UART5 (TLM); UART6 (receiver pads + rear SH1.0-4-pin)
ST LED Pads
Supported, on front G/5V/LED pads; controlled by FC firmware
Meteor LED Strip Pads
Supported. Switch between SB-LED and ST-LED modes via BOOT button or App. In SB-LED mode, controlled by ESP32 Bluetooth chip.
Buzzer Pads
Supported
BOOT Button
[A] Hold BOOT while powering on to force DFU mode for flashing.
[B] When powered and in standby, short-press cycles LED display modes; long-press switches SB-LED/ST-LED. In ST-LED mode, LED1–LED4 are controlled by FC firmware.
RSSI Pads
Supported
SmartPort
Not supported
Supported FC Firmware
Betaflight, INAV, Ardupilot
Firmware Target Name
SPEEDYBEEF405V5
Factory Firmware Version
Betaflight 4.5.2
Configurator Version
Betaflight 10.10.0
Mounting Holes
30.5 × 30.5mm (Ø4mm), side opening
Dimensions
39mm (L) × 39mm (W) × 4.9mm (H)
Weight
8.1g
Product Name
SpeedyBee OX32 55A 30.5×30.5 4-in-1 ESC
Default Firmware
OX32
Continuous Current
55A (per channel) / 220A (4-in-1)
Maximum Current
70A (per channel) / 280A (4-in-1)
TVS Protective Diode
Yes (built-in)
External Capacitor
1000µF Solid Capacitor (included in package)
ESC/Motor Protocol
DSHOT300/600
Input Voltage
3-6S LiPo
Power Output
VBAT
Current Sensor
Supported
ESC Telemetry
Supported
Mounting Holes
30.5 × 30.5mm (Ø4mm), side opening
Dimensions
40.9mm (L) × 44.9mm (W) × 8.0mm (H) (incl. heatsink)
Weight
19.1g
ESC Webpage
https://ox32.oxbot.com/
Current Meter Note
Supported (Scale=27, Offset=-2644)
Manual
中文
Product Name
SpeedyBee F405 V5 30.5×30.5mm Model Aircraft Flight Controller
MCU
STM32F405
IMU (Gyro)
ICM42688P
USB Port Type
New Type-C interface
Barometer
SPA06-003
OSD Chip
AT7456E
Full-featured Bluetooth Tuning
Supported. Connect via SpeedyBee App for FC firmware flashing and parameter tuning.
Wireless FC Firmware Upgrade
Supported
DJI Air Unit Connection
Supports 6-pin direct plug-in or solder connection
Blackbox
Supported, built-in 16MB storage chip
Input Voltage
3-6S LiPo battery
Independent 5V BEC Output
9 groups (4× +5V pads on front, 1× BZ+ buzzer pad, and 4× +5V pads at the corners for external LEDs). Total output current: 1.5A.
Independent 9V BEC Output
2 groups (1x 9V pad on front, 1x 9V output in a connector on the back). Total output current: 3A. Supports PINIO remote on/off control.
MCU & Gyro Power
Independent LDO
3.3V Output
1 group (1× 3.3V pad on front)
4.5V Output
3 groups (3× 4.5V pads on front). Can power receiver and GPS when FC is powered via USB. Max output current: 1A.
ESC Signal
M1-M4 pads and 10-pin connector on the back
Servo Signal
S5-S6 pads on the front
ESC Telemetry Input
Supported (UART5)
Betaflight Camera Tuning Pad
Supported (CC pad on front)
I2C
Supported (GPS connector + pads)
UART
UART1 (Bluetooth); UART2 (front pads for receiver); UART3 (DJI VTX pads + rear SH1.0-6-pin); UART4 (GPS pads + front SH1.0-6-pin); UART5 (TLM); UART6 (receiver pads + rear SH1.0-4-pin)
ST LED Pads
Supported, on front G/5V/LED pads; controlled by FC firmware
Meteor LED Strip Pads
Supported. Switch between SB-LED and ST-LED modes via BOOT button or App. In SB-LED mode, controlled by ESP32 Bluetooth chip.
Buzzer Pads
Supported
BOOT Button
[A] Hold BOOT while powering on to force DFU mode for flashing.
[B] When powered and in standby, short-press cycles LED display modes; long-press switches SB-LED/ST-LED. In ST-LED mode, LED1–LED4 are controlled by FC firmware.
RSSI Pads
Supported
SmartPort
Not supported
Supported FC Firmware
Betaflight, INAV, Ardupilot
Firmware Target Name
SPEEDYBEEF405V5
Factory Firmware Version
Betaflight 4.5.2
Configurator Version
Betaflight 10.10.0
Mounting Holes
30.5 × 30.5mm (Ø4mm), side opening
Dimensions
39mm (L) × 39mm (W) × 4.9mm (H)
Weight
8.1g
Product Name
SpeedyBee OX32 55A 30.5×30.5 4-in-1 ESC
Default Firmware
OX32
Continuous Current
55A (per channel) / 220A (4-in-1)
Maximum Current
70A (per channel) / 280A (4-in-1)
TVS Protective Diode
Yes (built-in)
External Capacitor
1000µF Solid Capacitor (included in package)
ESC/Motor Protocol
DSHOT300/600
Input Voltage
3-6S LiPo
Power Output
VBAT
Current Sensor
Supported
ESC Telemetry
Supported
Mounting Holes
30.5 × 30.5mm (Ø4mm), side opening
Dimensions
40.9mm (L) × 44.9mm (W) × 8.0mm (H) (incl. heatsink)
Weight
19.1g
ESC Webpage
https://ox32.oxbot.com/
Current Meter Note
Supported (Scale=27, Offset=-2644)
Manual
中文
